VR2536-X 3 Axis Motion Open Bed using 4 motors and 4 drivers.
25" x 36" CNC Router
Cut 2D composite or 3D wood relief with this foot cnc router machine. The supported X and Y axis provide a rigidity, high tolerance positioning, and cut accuracy. Dust resistance lead screws are very we suited for projects that produces a lot of powder, wood chips, foam dust, and more dusty outcomes. With our 110V/220V control box using the proven gecko drive and high torque stepper motors you can use this machine in your garage, warehouse, business, or school with little or no investment to power upgrades. Our anti backlash lead screws and nuts provides great resolutions and accuracy.
Please contact us for pricing.
Image above is of 36x36 cnc router.
Up to date software, hardware, and technology.
Free 4 hours of Training at VELOX CNC, online, email, or GoToMyPC.
Reliable and proven Gecko Drives.
Rigid supported rails on X and Y axis.
Accurate anti backlash motion and resolution.
Assembled and tested.
25" X 36" x 8"
25" (motion left and right)
36" (motion forward and back)
8" (CUSTOMIZABLE - CALL US)
110V - 220V
X AXIS CLEARANCE
Z AXIS CLEARANCE
5.5" after .75" table installed.
5/8"-8 WITH 2 STARTS (.250" TRAVEL PER TURN)
(2 QTY) LEADSCREW Y
5/8"-8 WITH 2 STARTS (.250" TRAVEL PER TURN)
1/2"-10 WITH 1 STARTS (.100" TRAVEL PER TURN)
STEPPER - GECKO DRIVE
570 OZ/IN - Set to 150 IPM
MOTOR Y, AND A
380 OZ/IN - Set to 250 IPM
280 OZ/IN - Set to 100 IPM
OPEN BED - Y AXIS HAS EXTERNAL DRIVES.
Cutting carbon/fiberglass with .001" results. Great circles and bolt holes all made using a .125" caride endmill.
Would have been better results with a precision collet kit.
VR3636 Cutting 6061-T6 aluminum with a 0.050" step down pass for a total depth of 0. 500" deep pockets and .75" depth cut on the outter side walls. We used a Porter Cable 892, a .250" 2 flute carbide endmill with the RPM set to 23,000. Visualmill was used as the CAM software.
VR3636 Cutting polycarbonate with a .500" diameter endmill. A 0.250" step down pass for a total depth of 0. 500" deep. We used a Bosch 1617, 2 flute carbide endmill with the RPM set to 20,000-23,000. 45IPM for roughing and 20IPM for finishing. Visualmill was used as the CAM software. 4 bridges were used to hold down the part. We would use a vacuum for better cut quality.
VR3636 Cutting wood with a .500" diameter endmill. A 0.34" step down pass for a total depth of 1.300" deep. We used a Bosch 1617, 2 flute straight carbide endmill with the RPM set to 20,000-23,000. 30iPM for all cuts. Visualmill was used as the CAM software.
VR3636 Cutting a 3D eagle out of wood with a .500" diameter ball endmill. We used a Bosch 1617, 2 flute straight carbide endmill with the RPM set to 20,000-23,000. 30iPM for all cuts. Vectric Cut 3D was used as the CAM software.
Computer with Parallel Card configured for dedicated Mach 3.
Porter Cable 892 Router.
Aluminum Table Top
Please allow a VELOX sales representative to assist with your cnc options. call 714-639-3639
Colt precision collet.
+ Increase precision a run-out of . 003" or .005" to a .0005" run-out. Ground collets.
Brass 1/8th inch collet holders.
+ Holds 1/8th bits with better accuracy compared to off the shelf adapters.
Assembly of Machine: At VELOX CNC, we test the controller and tolerance prior to shipping the machine.
It is important to us that our customers get up and running as soon as possible. You would just have to plug in the wires to the control box, connect the computer, and install the router onto the machine. We would be happy to be on the phone as you start up the machine.
One year on parts based on an 8 hours per day, 7 days per week operation.
One year on labor at VELOX CNC location in California.
4 hours of training one Mach 3 or Cam software sold by VELOX CNC with purchase of machine and control box.
Support on machine:
Email - unlimited.
Phone - unlimited.
Support on software:
Mach 3 - Unlimited only with purchase of machine, control box, and Mach 3.
Visualmill - 4 hours with purchase. ($400 value)
Vectric - 4 hours of training with purchase ($400 value)
Crating and Handling: The majority of the cnc machines are crated in a wooden pallet or a crate using plywood, 2x2 and 2x4.
All machines are insured for the price you paid for the machine and are FOB Orange CA 92867.
Fork Lift: A fork lift will be require unless otherwise stated in writing from VELOX CNC.
Lift Gate: A lift gate may be available, but is not guaranteed. Please request a lift gate when you ask for a quote.
We use shipping brokers as well as UPS-SCS to ship your machine safely and on time.
Please contact us and provide your full address and shipping details so that provide you an accurate shipping charge.